The heavy duty Rack and Roll shocks, part # Y08110, can only be used on 66 inch Rack and Roll if you upgrade it with the 78 inch crossmember kit. The crossmember kit is part # Y08111.
The 66 inch trailer is rated up to 250 pounds so as long as you're under that capacity there really isn't a need to upgrade it. It would just give you some peace of mind. view full answer...
When using the Tow Ready Mounting Bracket # 18144 to mount the 4-way trailer connector from the Curt T-Connector Vehicle Wiring Harness # 56083, you should not have to cut the harness in any way. After installing the mounting bracket, you will simply route the 4-way through the bracket opening and input the cap on the end of the connector. The opening on the bracket is 1-3/8 inches in length horizontally. You can use the bracket along with the short bracket # 18140 for a no drill application.... view full answer...
There there are two things that will help you find the install connectors on your vehicle to install this harness # 118255.
1. The T-One Vehicle ModuLite portion with the in-line fuse holder connects through the rear cargo area on the passenger side. It connects to the 10-pin plug included in your Lexus. The attached diagram should help in locating the access point and where the connection will be made.
2. The 4-way tow harness plug connects to the the trailer connection installs at... view full answer...
To install the Tow Ready T-One Vehicle Wiring Harness 4-pole # 118255 on a your 2012 Lexus RX 450H, the white plug that has a small black box attached to it plugs in to the vehicle wiring harness. This attachment point is located in the rear cargo area of your vehicle, and is on the passengers side. Then the gray plug that has the trailer 4-pole at one end will plug into the connection point underneath your vehicle. There is also a 10 amp mini-fuse included in this kit and that will have... view full answer...
Yes, that is consistent for your 2014 Lexus RX 450h as well. I checked the online owner's manual for your vehicle and the fuse locations were the same. You can verify this with your copy of the owner's manual as well. I found the fuse location charts started on page 694.
If you do have the factory tow package then part # 118252 is what you are needing. If you do not have the factory tow package then the T-One # 118255 is what you need instead. This has the same wiring harness for the 4-Way... view full answer...
Hanging style bike racks like the Hitching Post Pro # TH934XTR have the tilt away feature but it's meant to be used without the bikes loaded. If you wanted a hanging style bike rack with the ability to access your rear hatch, you'll need something like the Thule Apex Swing # TH9027XT. The only other option is to get this swing away adapter # SAR36VR which can be used with multiple bike racks along with a cargo carrier. The weight capacity of the swing away is 250 lbs. view full answer...
On the protective cap covering the connection point for trailer wiring on the 2010 Lexus RX 450h, there will be a locking tab on one side. You will need to push in the locking tab with your thumb and at the same time pull the cap off. When you go to connect harness # 118252 the locking tab on it will snap into place on the factory connector. I have included a link to the installation instructions for you. view full answer...
I have included the instructions for the Hidden Hitch by Draw-Tite Trailer Hitch Receiver # DT58GR for your 2022 Lexus RX 450h below. You will need the Threaded Quick Links # RM-910022 to attach your trailer chains if you will be using the hitch for towing. These are needed as the holes for the attachments are very small and will not fit most trailer chain hooks.
The T-One Vehicle Wiring Harness # 118252 will allow you to connect to the factory connector(see image) for towing if your... view full answer...
The best way to add a 7-way trailer connector onto the back of your 2017 Lexus RX 450h that already had a 4-way connector is with # ETBC7. This gives you all the components needed for a fully functioning 7-way and comes with the instructions, which are attached. view full answer...
The Draw-Tite Trailer Hitch, # 75676, for the 2010 Lexus RX450h installation is rated as moderate difficulty. The difficulty ratings are easy, moderate and hard. A second person would help the installation go a little easier.
You would need to remove the lower fascia underneath the back of the vehicle. It will need to be trimmed and reinstalled after the hitch is installed. There are two tow loops that will need to be removed, one on the drivers side frame rail and one on the passengers... view full answer...
If you haven't plugged in the converter box portion of wiring harness # 118255 (the part with the yellow fuse holder) then the 4-Way will not work until you do. Inserting the fuse in the fuse holder would be the last step.
This harness is circuit protected. This means that if there is a short on the trailer it will not damage the vehicle wiring or electronics.
You should not have to have the vehicle computer flashed or reprogrammed to use the harness. view full answer...
The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 75676 is a confirmed fit for your 2014 Lexus RX 450h. We do not have any videos of the RX450h with that particular hitch receiver, but I have added the video of the installation of the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13143 which is also a fit to assist. view full answer...
In order to keep the vehicle on the dolly stable and tracking properly behind the motorhome or vehicle doing the towing, you'll want to keep the towed vehicle's steering wheel locked at all times. This applies whether or not the tow dolly in question is 'self steering' or has a steer axle.
I've linked you to some demonstation/description videos featuring the Roadmaster # RM-2050-1 tow dolly you'd looked at. view full answer...
Go To Results